Water on board

Showing 1–24 of 279 results

120° elbow hose tail (male) Trudesign

 

TruDesign Long Thread 90° Tails are designed to screw into the range of Ball Valves but can also be used in many applications. Moulded in glass-reinforced nylon composite these Tails are also suitable for use in contact with petrol and diesel fuels.

TruDesign Tails eliminate the corrosion and electrical bonding problems associated with metallic fittings. Tail fittings are designed for twin hose clamps, and to never crush.

ISO 9093-2 και ABYC H27.

90° elbow (male-female) Trudesign

 

TruDesign Connectors are moulded from a glass reinforced nylon composite. High strength, high-modulus glass fibres impregnated into the nylon provides dramatic strength, stiffness, toughness, and dimensional stability.

TruDesign Connectors eliminate the corrosion and electrical bonding problems associated with metallic fittings.

ISO 9093-2 και ABYC H27.

For more information please click  here.

90° elbow fitting Whale

Whale Quick Connect fittings ensure a high integrity, reliable, plumbing system solution, specifically designed for use in mobile applications

WX15 fittings and pipework design ensures easy installation and re-usability of components. The simple two step installation procedure does not require special tools to make a watertight connection.

  • Unique ‘WX15 Double Gripper’ design provides secure lifelong pipework retention even at excessive pressures
  • The innovative ‘cage collet’ eliminates leaks where fittings are installed close to tight bends
  • Collet has internal support ring ensuring o ring seal is held in position and does not distort or leak under pressure
  • High integrity single piece moulding improves the strength of the fittings
  • Outer sleeve incorporates collet cover, thus preventing accidental pipework release
  • Collet clips are not necessary and therefore reduce installation time
  • Pipework includes measured cut marks, designed to be a visual guide to ensure that fittings are pushed fully

90° elbow hose tail (female) Trudesign

 

TruDesign composite fittings are moulded from a glass-reinforced nylon composite. High strength, high-modulus glass fibres impregnated into the nylon provide dramatic strength, stiffness, toughness, and dimensional stability.

TruDesign fittings eliminate the corrosion and electrical bonding problems associated with metallic fittings. Tails (Hose barbs) are designed for twin hose clamps and to never crush.

ISO 9093-2 και ABYC H27.

Fore more information click here.

90° elbow hose tail (male) Trudesign

TruDesign Long Thread 90° Tails are designed to screw into the range of Ball Valves but can also be used in many applications. Moulded in glass-reinforced nylon composite these Tails are also suitable for use in contact with petrol and diesel fuels.

TruDesign Tails eliminate the corrosion and electrical bonding problems associated with metallic fittings. Tail fittings are designed for twin hose clamps, and to never crush.

ISO 9093-2 και ABYC H27.

For more information please click here.

Accumulator tank 0,7Lt Shurflo

 

Reduce cycling pulsation and pressure spikes, increase the life of your pump and even save battery power. Easily handles pressure requirements from 20 PSI to 125 PSI.

  • Reduces pump cycling
  • Smooths water faucet pulses
  • Pre-pressurized to 30 PSI with built-in diaphragm
  • Supported for industrial and marine

Accumulator tank 2lt Johnson

 

  • For installation in any pumped water system controlled by a pressure switch up to max 12 bar (174 PSI) operating pressure
  • The Accumulator tank smooths water flow and reduces on/off cycling of the pump by lessening the variation in pressure and flow between the pump and the outlets in the system
  • Reduces noise, battery drain and improves pump life
  • Mounts in any position
  • Retainer for mounting included

Manual:

Accumulator tank Jabsco


Accumulator tanks enhance the performance of their pressure pumps. An accumulator tank is a water chamber which has a pre-pressurized internal air bladder. They are installed in the pressured side of your pump and dampen water pressure ‘spikes’, reduce pump cycling, help increase the pump’s life and also save battery power.

May be mounted in any attitude.

Accumulator tank Marco

White coated and stainless steel accumulator tank for automatic pumps.

Technical data sheet:

 

Anode for water heaters resistances

 

Magnesium anode intended mainly for resistances of QUICK water heaters.

Anti-odor active carbon filter

Active carbon filter for black waters tank’s vent complete with bracket and rubber hose terminal Ø 20/25 and length 200 mm.

Should be installed along tank vent in the highest possible position.

The activated carbon should not come n contact with the liquid.

The filter should be replaced each year.

Attwood deck shower system


Install flush in the transom or under the gunwale. Includes hinged cover and replaceable sprayer head.

Fixtures are corrosion-resistant. Housing and cover are made of high-impact, UV resistant, engineering-grade plastic and are pre-drilled for six #8 fasteners.

Comes with 6’ hose, shut-off and hot/cold mixing controls. Connects to freshwater system for showering.

Automatic bilge pump Rule

  • Fully automated operation
  • Tough plastic body with integral strainer
  • Quick release strainer allows rapid cleaning
  • Low amp draw conserves batteries
  • Checks for water every 2 1/2 minutes (Runs for 1/2 second)
  • Consumes 0.20 amps per day
  • Built-in thermal cut-off
  • Check Valve included for back flow prevention
  • Vented body to prevent air locking
  • Threaded port for easier installation and maintenance
  • No Need for separate float switch, third wire for manual override

Automatic bilge pump Sahara Attwood

Combine sturdiness, simplicity of use and high efficiency:

    • Motor is automatically operated by a reliable mechanical float switch (non toxic ; contains no mercury).
    • Shaft seal and caulked wiring provide extra protection to the motor, preventing leak paths. The free flow of water around the motor housing keeps motor cool for extended life.
    • 316 stainless steel motor shaft for saltwater corrosion resistance. Steel reinforced motor shaft ensures perfect alignment of shaft and seal, thus preventing leaks.
    • Durable impeller is made of tough, high-impact, glass filled polyester.
    • Re-enforced filter for optimum protection of the impeller.
    • Test knob allows for easy and immediate operational check without disassembly.
    • Compact size and low-profile design allow installation in tight places.

Sahara Mk2 is the only automatic bilge pump that eliminates air-locks. Its engineered performance forces air bubbles trapped in the hose and underside of the pump out of the pipework, so that the pump will not run dry and burn out.

This breakthrough technology makes Sahara Mk2 the most reliable automatic bilge pump in freshwater and saltwater applications. 

Brochure:     Datasheet:

       

Automatic float switch TMC

Automatic float switch to work with bilge pumps drawing under 10Amp.

Can be used with either 12V or 24V.

 

Automatic low profile bilge pump TMC

Automatic low profile bilge pump designed for confined or tight space (under engines or cockpit floors).

Automatic operation with sensor. Drains down as low as 10mm.

Strainer can be rotated & cover can be removed for easy cleaning.

Holes on top to prevent airlocks. Also, the outlet port can be rotated for different installation purpose (vertical or horizontal mounting).

Ball Valve Bronze Italy

Bronze body F.F. full port ball valve with stainless steel handle.

Showing 1–24 of 279 results

X