Accumulator tank 0,7Lt Shurflo
Reduce cycling pulsation and pressure spikes, increase the life of your pump and even save battery power. Easily handles pressure requirements from 20 PSI to 125 PSI.
- Reduces pump cycling
- Smooths water faucet pulses
- Pre-pressurized to 30 PSI with built-in diaphragm
- Supported for industrial and marine
Anti-odor active carbon filter
Active carbon filter for black waters tank’s vent complete with bracket and rubber hose terminal Ø 20/25 and length 200 mm.
Should be installed along tank vent in the highest possible position.
The activated carbon should not come n contact with the liquid.
The filter should be replaced each year.
Attwood deck shower system
Install flush in the transom or under the gunwale. Includes hinged cover and replaceable sprayer head.
Fixtures are corrosion-resistant. Housing and cover are made of high-impact, UV resistant, engineering-grade plastic and are pre-drilled for six #8 fasteners.
Comes with 6’ hose, shut-off and hot/cold mixing controls. Connects to freshwater system for showering.
Bilge strainer plastic (side entry)
This bilge strainer is made out of oil-resistant plastic.
The built-in check valve prevents backflow and facilitates suction.
With side entry.
Bilge strainer plastic Whale
This bilge strainer is made out of oil-resistant plastic.
The built-in check valve prevents backflow and facilitates suction.
With top or side entry.
Case for shower head and mixer
Oval plastic case for shower head and mixer.
Case with cold water tap
Case with cold water tap with lid, connection /2″F x 1/2″F.
Deck mixer tap set with cover Plastimo
Functional and safe hinged cover. Splashproof when closed.
With white the housing fits snugly in any deck or transom of sail and power boats, to give a clean uncluttered look.
Flush installation in transom or deck only requires a Ø70 mm hole, easily done with a hole saw. The housing requires minimal depth for installation and accepts most existing shower heads.
Discharge port 44107-1000 1″ (25cm) Jabsco
Replacement discharge port for Jabsco electric toilets.
# 12 in the exploded view
Inlet non-return valve Jabsco
A check valve gives quicker and easier flushing response on many manual and 37010-Series electric toilet installations.
- For use with manual and electric toilets using sea water flush
- Simply fit inlet suction hose, near seacock but just above waterline
- Retains water in bowl of 37010-Series electric toilets installed above waterline
Inline water filter
Inline water strainers with transparent lid and internal stainless steel filter.
Load bearing Trudesign
TruDesign load bearing collars are designed for use with Trudesign skin fittings and ball valves.
With the collar in place, the skin fitting-ball valve-hose tail assembly will withstand a 500 lb (227 kg) static force applied to the Hose Tail end of the assembly, for a minimum of 30 seconds – complying with North American ABYC H-27 standards.
Note: Trudesign 2″ skin fittings meet the requirements of H-27 500Lb standard (i.e. without a Large Collar installed). Adding a large collar to assemblies of this size increases the overall strength and protects the vulnerable exposed section of thread on the Skin Fitting.
Non return valve Trudesign
TruDesign Non-Return Valves (Check Valves) are made from UV stabilised glass reinforced nylon, these composite material fittings are designed for the harsh marine and agricultural environments.
They can be used in line to prevent water backflow or siphoning and have a very low cracking pressure. High strength and lightweight. Can be used in direct sunlight. Minimal installation room needed and no other fittings required.
Non-return valve
Non-return valve that allows the drainage of water from points where it is collected while at the same time does not allow the inflow.
External diameter 70mm and internal diameter 50mm.
Plastic black through-hull
Suitable for underwater use, TruDesign range of Skin Fittings are certified by the International Marine Certification Institute (IMCI) and Bureau VERITAS to ISO 9093-2.
They also comply with ABYC H-27 when used in conjunction with the TruDesign ABYC collar.
Designed and made in New Zealand, the Skin Fitting body and nut are moulded from a glass-reinforced nylon composite. High strength, high-modulus glass fibres provide dramatic strength, stiffness, toughness and dimensional stability. These properties allow a significant weight reduction over metallic fittings.
- Manufactured from a glass-reinforced nylon composite – High strength and light weight
- Compatible with all hull types – Can be used on aluminium, steel, wood or GRP hulls
- Immune to corrosion and electrolysis – Long life with no concerns over decreased performance due to corrosion
- Chemical resistant – Impervious to diesel, petrol and antifouling paints
- UV resistant – Will not degrade or discolour with ultraviolet light from the sun
- High quality surface finish – Will not discolour with green film as similar bronze fittings do
- Paintable – Can be painted with all types of antifouling
ISO 9093-2 & ABYC H27 Certified
Plastic corner sink
Made from polypropylene which is shock and stain resistant.
Cutout Ø38.
Supplied complete with plug and chain.
Plastic through-hull 90°
White PVC threaded through hull with hose connection.
Round water heater inox- plastic Quick
The Quick Model B3 is a round water heater that produces water from an incoloy electric heating element that is fitted with an adjustable safety bi-thermostat.
This unit is equipped with a heat exchanger composed of AISI 316L stainless steel with a capacity that is notably higher than that achieved from other manufacturers.
The interior of the tank is made of 1.5 mm gauge AISI 316 stainless steel welded with Argon shielding gas which enables it to be highly resistant to corrosive agents. The exterior of the tank is composed of a highly durable plastic composite material. The unit has thermal insulation composed of high density polyurethane foam which is injected between the cover and tank thus providing excellent heat retention properties.
The boilers are equipped with a heat exchanger for the engine cooling water.
The B3 unit also comes with adjustable metal brackets which provide more flexibility for mounting when dealing with tight spaces.
This unit comes equipped with the water heater, mounting brackets, and 4 brass fittings.
